** WWW.NINJAMOD.COM **
NINJAMOD'S 1.4 BIOS :
DISC IDENTIFY
AUTODETECTS VIDEOMODE
RUNS DVD-R/DVD+R BACKUP/ORIGINAL DISC
FASTER DISC ACCESS
LESS DRE'S THAN OLDER BIOS
VIDEOMODE REALTIME CHANGE,NO NEEDED SAVE SETTINGS (NO NEEDS SOLDER F)
NETWORK IP'S REALTIME CHANGE,NO NEEDED SAVE SETTINGS (NO NEEDS SOLDER F)
NONSWAP BIOS 2 UPDATE by DVD-R or NETWORK FLASHING
This version has LESS DRE'S than older versions ... improving the reading
in DVD-R Media,it's almost perfect we're going to add DVD+R support in later versions too ...
NOTE : Some 6 drives(not all) need to be tweaked...ALL the discs working with swap method,
will work with this version ...if no works,it's not good media or need a tweaking..
For those which can't make work our BIOS's or have probs installing perhaps you're too beginner and you need some technical help by Local professional ...
anyway we make you some HINTS:
UPDATING THE BIOS :
From BIOS1 ,Just Burn the ISO to a DVD+R or DVD-R (depends your DVDlent calibration) select UPDATE BIOS 2and
make a SWAP METHOD set the bios file and press A when ordered ...
From BIOS2 , with lastest 1.02 version (dvd-r nonswap) ,burn the ISO in a DVD-R and select UPDATE FROM Menu
HOW TO BURN THE BIOS :
Open NERO BURNING ROM ....SELECT BURN IMAGE ... IGNORE BLOCK SIZE ... SELECT DVD IN THE CORNER OF THE NEW WINDOW,
you can set "OPENED" DVD for faster burning ....
INSTALLING THE NINJAMOD :
*DO NOT USE long wires,all ones MUST be medium size maximum..This is very important for X and B point.....if wire are long on these points Ninjamod will not boot....
*We recommend install ALTERNATIVE POINTS scheme if you haven't soldering skills......
*We recommend install the ninjamod without the F point,after you check the Ninjamod boots ... use that point if it's your choice .....with this new version point F is just needed to save changes or run the original bios..
*USE Medium or good Quality DVD-R/DVD+R media,bad DVD-R/DVD+R will no boot,or will produce DRE'S or
bad readings ....
** WWW.NINJAMOD.COM **
NINJAMOD'S 1.4 BIOS :
DISC IDENTIFY
AUTODETECTS VIDEOMODE
RUNS DVD-R/DVD+R BACKUP/ORIGINAL DISC
FASTER DISC ACCESS
LESS DRE'S THAN OLDER BIOS
VIDEOMODE REALTIME CHANGE,NO NEEDED SAVE SETTINGS (NO NEEDS SOLDER F)
NETWORK IP'S REALTIME CHANGE,NO NEEDED SAVE SETTINGS (NO NEEDS SOLDER F)
NONSWAP BIOS 2 UPDATE by DVD-R or NETWORK FLASHING
This version has LESS DRE'S than older versions ... improving the reading
in DVD-R Media,it's almost perfect we're going to add DVD+R support in later versions too ...
NOTE : Some 6 drives(not all) need to be tweaked...ALL the discs working with swap method,
will work with this version ...if no works,it's not good media or need a tweaking..
For those which can't make work our BIOS's or have probs installing perhaps you're too beginner and you need some technical help by Local professional ...
anyway we make you some HINTS:
UPDATING THE BIOS :
From BIOS1 ,Just Burn the ISO to a DVD+R or DVD-R (depends your DVDlent calibration) select UPDATE BIOS 2and
make a SWAP METHOD set the bios file and press A when ordered ...
From BIOS2 , with lastest 1.02 version (dvd-r nonswap) ,burn the ISO in a DVD-R and select UPDATE FROM Menu
HOW TO BURN THE BIOS :
Open NERO BURNING ROM ....SELECT BURN IMAGE ... IGNORE BLOCK SIZE ... SELECT DVD IN THE CORNER OF THE NEW WINDOW,
you can set "OPENED" DVD for faster burning ....
INSTALLING THE NINJAMOD :
*DO NOT USE long wires,all ones MUST be medium size maximum..This is very important for X and B point.....if wire are long on these points Ninjamod will not boot....
*We recommend install ALTERNATIVE POINTS scheme if you haven't soldering skills......
*We recommend install the ninjamod without the F point,after you check the Ninjamod boots ... use that point if it's your choice .....with this new version point F is just needed to save changes or run the original bios..
*USE Medium or good Quality DVD-R/DVD+R media,bad DVD-R/DVD+R will no boot,or will produce DRE'S or
bad readings ....
** WWW.NINJAMOD.COM **
