jkyoho's latest activity
-
jkyoho replied to the thread Hacking Need help exiting autoboot on hekate 5.0.1.bootwait=3 always give me some room when regret -
jkyoho reacted to Chary's post in the thread Nintendo officially confirms Switch successor console, announces Nintendo Direct for next month with
Like.
While rumors had been floating about rampantly as to the future plans of Nintendo, the President of the company, Shuntaro Furukawa, made a brief statement confirming that Nintendo is indeed working on a successor to the Nintendo Switch. Capping... -
jkyoho replied to the thread Nintendo Switch lite with Picofly.remove payload.bin from root sdcard and ignore "No SD" logo is the easiest way to use it only on OFW
-
jkyoho replied to the thread PS5 EDM-010 missing component under HDMI ic chip.Cant find the YD label one but this one label with 31 is from Rohm part# DTA044EUB https://fscdn.rohm.com/en/products/databook/datasheet/discrete/transistor/digital/dta044eubtl-e.pdf
-
nope since signature patches aren't active unless you boot hekate or sys-patch
-
You should create an emummc (emulated copy of your Switch internal memory - sysmmc). Then you use sysmmc for you official games and emummc for your unofficial games and homebrew. That way you can play the games you bought online in sysmmc...
-
jkyoho replied to the thread Hardware Dead ps5 PSU adp-400gr.https://www.a-power.com.tw/en/product/download/AP6NA3R5H/datasheet PACKAGE should be TO-252
-
jkyoho replied to the thread Hardware Is the thermal pad on the battery charging chip necessary?.I notice the 2R2 inductor next to BQ would heat up around 70C when playing&charging, not sure how BQ goes but the thermal pad definitely help
-
jkyoho reacted to Hayato213's post in the thread Issues after restoring nand and updating to fw 17+ with Like.
If your fuse count is 19 it explain why your OFW wouldn't boot firmware 16.1.0 as it expect firmware 17.0.0 to 18.0.1. Should always keep a copy of your original NAND, you wouldn't have this problem if you have your own NAND backup, using the...
-
jkyoho replied to the thread Picofly AIO Thread.looks good. top side Extra gnd seems unnecessary though. The two square ground pads under cap could help stopping flex moving Around, I would say keep them.
-
jkyoho replied to the thread Oled Volume Resistor.doubt that's an inductor but not resistor. Based from OG and lite design, there are always 100~150 ohm resistor on buttons
-
jkyoho replied to the thread Somewhat Confused here?.delete cfw-syanad entry from hekate_ipl.ini and enable dns_mitmfrom day1, you should be 2steps away from dirty sysnand
-
jkyoho replied to the thread Help Accidently blue screened my switch!!!.file transfer can be done through Hekate(even from another switch). Boot 0/1 can be generated from emmchhaccgen on PC with prod.key from the Blue screen console. If you can't/don't know how to make unpatched switch into RCM mode, you are on your own.
-
jkyoho replied to the thread Hardware Power supply problem.Switch battery voltage max out at 4.23v-ish, 3.9v is pretty much closed to 90% charged, NOT VERY LOW. Also If you are expecting 15v goes into the battery terminal, I think you would see some popcorn out of your battery BMS board. This battery...
-
-
jkyoho replied to the thread Help Accidently blue screened my switch!!!.So you are on HOS FW 18.0.0. Hekate 6.1.1 and AMS 1.7.0prelease should be able to support this verison. I believe you need to rebuild you nand using Tegraexplorer system_wipe to FW18.0.0
