Found it. Works great. Thanks.check previous releases. i think i omitted that file in recent releases
Found it. Works great. Thanks.check previous releases. i think i omitted that file in recent releases
it does not have serial number hiding and plus there are no sig patches. Again, not that, I just need a working version and that’s it, someone’s backup.
It actually has both.it does not have serial number hiding and plus there are no sig patches. Again, not that, I just need a working version and that’s it, someone’s backup.
Just got into OC-Suite and loving it, though while i know i can change settings from the applet on the go does anyone knows if there's a working Tesla overlay that works with the current build of OC-Suite and 17.0.0 HOS?, looking with the search through here, google, reddit, youtube, etc but couldn't find one.
Damn it. What am I doing wrong. My serial number has opened. I took what you indicated and unpacked it into a folder. And I got a system that didn't work. At first there was a blue screen, I had to choose what I needed to launch without an emunand, and then nothing worked for me, games didn’t start, overclocking didn’t work. Damn it, I just put it on a flash drive and that’s it, is there anything else that needs to be done?It actually has both.
Друг ты же ловец на хлебном поля из чата чифира, скажи пожалуйста что я делаю не так. Я просто хочу использовать свитч ОС, но она не работает, точнее то не запускает приложения то не скрывает мой серийник то вообще нет разгона ОЗУ. Может я туплю. Пожалуйста скинь мне свой БЕКАП рабочий или подскажи что я делаю не такДонагрузить
You need to edit your loader.kip in the following page https://hanai3bi.github.io/Switch-OC-Suite/#configAm stumped a bit with this software. I can figure out how to take my memory clock above and beyond but how do I enable a higher GPU and CPU clock?
No matter what I do on my oled switch,with the overlay I can only see 998mhz for the GPU and 1963 for the CPU. How do you allow these to go higher?
You need to edit your loader.kip in the following page https://hanai3bi.github.io/Switch-OC-Suite/#config
Then replace the original with the new one you generated, be sure to use safe OC numbers for your console version.
Am stumped a bit with this software. I can figure out how to take my memory clock above and beyond but how do I enable a higher GPU and CPU clock?
No matter what I do on my oled switch,with the overlay I can only see 998mhz for the GPU and 1963 for the CPU. How do you allow these to go higher?
Place this line allow_unsafe_freq=1 under [values] section in /config/sys-clk/config.ini to enable higher frequencies. Make sure you enable CPU UV2 and GPU UV2 at least before use higher clocks though.
I've already added that line in my config file but it still doesn't give me any other options. I haven't done the CPU and Gpu uv2 yet, would that be stopping the higher clocks even showing?
frequency tables are parsed only one time at boot (on purpose), so you need to reboot after toggling unsafe frequenciesI've already added that line in my config file but it still doesn't give me any other options. I haven't done the CPU and Gpu uv2 yet, would that be stopping the higher clocks even showing?
Use this config:Am stumped a bit with this software. I can figure out how to take my memory clock above and beyond but how do I enable a higher GPU and CPU clock?
No matter what I do on my oled switch,with the overlay I can only see 998mhz for the GPU and 1963 for the CPU. How do you allow these to go higher?
allow_unsafe_freq = 1
uncapped_clocks = 1
that is correct behavior. mariko has only 3 tables available unlike erista.Hey!
I think I have done everything correctly.
My default memclock on a Mariko switch became 1600mhz. Is this the correct behaviour or did I mess something up? OC works fine. Awesome sw.
Could not connect to sys-clk.
Please make sure everything is correctly installed and enabled.
sysclkpcSetProfiles
[0x584] 0388-0002