Recent content by Gamefreak001

  1. Gamefreak001

    Micro sd card reader - Switch Lite

    Donor board.
  2. Gamefreak001

    Unable to charge - when connected to computer but is fine with power bricks

    I got a usb tester on this unit and saw that it only charges at 0.47amp. It does not go to fast charge. That might be the main issue. I have swapped out the usb c port and the m92 chip and it still unable to go into fast charge. I found no shorts around the m92, BQ and PI3usb chips. Running out...
  3. Gamefreak001

    Unable to charge - when connected to computer but is fine with power bricks

    Yes. I have done the troubleshooting steps and isolated to this switch. 1699133854 I can do microsoldering, just horrible at troubleshoot which component has failed. 😂
  4. Gamefreak001

    Unable to charge - when connected to computer but is fine with power bricks

    Sometimes it would connect over DBI. When it is connected, I still get that error message about not charging. When it does connected with DBI, the transfer speed is extremely slow. Over 50+ mins to install instead of the normal 5-10mins. I have other switches and they connected fine with the...
  5. Gamefreak001

    Unable to charge - when connected to computer but is fine with power bricks

    It display the error with an X next to the battery.
  6. Gamefreak001

    Unable to charge - when connected to computer but is fine with power bricks

    I have a regular Switch that has no issue charging to a power brick or plug, but will not charge by a computer. I have tried multiple computers and usb ports and they all behave the same way. Must be some ic chip issue. Anyone comes across this issue before?
  7. Gamefreak001

    Switch Lite draining battery fast (even when it is powered off)

    Those are chips on the board.
  8. Gamefreak001

    Switch Lite draining battery fast (even when it is powered off)

    I have a Switch Lite that drains battery fast. About 10% in 5-10mins. If I am at 95% battery and power it off completely overnight, the next morning it is at 10%. It’s not the battery as I have it disconnected and the charge remains at the same voltage reading with a multimeter. I replaced the...
  9. Gamefreak001

    Hwfly rp2040 on oled, inconsistent boot

    When I switch over to the instinct chip, it doesn’t get stuck like in the hwfly chip. It still doesn’t boot into hekate all the times. 1694448957 Still not yet. I might open the switch and resolder a few points. Just haven’t have time yet to try.
  10. Gamefreak001

    Micro sd card reader - Switch Lite

    This issue is still outstanding. I compared this board with a working one and something else is causing this, not the physical micro sd slot. I just don’t have enough electric engineering background to troubleshoot this. This will sit in my pile until I have more experience in troubleshooting.
  11. Gamefreak001

    Tip to solder the ribbon cable for Switch Lite

    Is there any trick or tip on soldering points A and D on the ribbon? The gap between the board and the ribbon is quite far. I always spend too long doing these two points.
  12. Gamefreak001

    Micro sd card reader - Switch Lite

    Already replaced the sd card reader an hour ago and that didn’t help fix the error. What is this blue smd? I am comparing diode values between another working board and I am not getting any value at this component. I am getting 0v instead of 0.57v.
  13. Gamefreak001

    Micro sd card reader - Switch Lite

    Replaced the sd card reader and that didn’t fix the issue. Something else is causing this issue, just don’t know which one to try.
  14. Gamefreak001

    Micro sd card reader - Switch Lite

    Thanks! I wanted to confirm with others before I try replacing it.
  15. Gamefreak001

    Micro sd card reader - Switch Lite

    I have a Switch Lite that cannot read sd cards. I have tried different cards and still can’t read it. I get the following error message: Error code 2016-0641 unable to access media If I replace the micro sd reader, will that fix the issue or is there some kind of ic chip that I have to look...
General chit-chat
Help Users
  • No one is chatting at the moment.
  • K3Nv2 @ K3Nv2:
    why
  • Xdqwerty @ Xdqwerty:
    @K3Nv2, it's not funny
  • K3Nv2 @ K3Nv2:
    ok
  • BigOnYa @ BigOnYa:
    Wut?
  • K3Nv2 @ K3Nv2:
    That's not funny
    +2
  • Psionic Roshambo @ Psionic Roshambo:
    So two cannibals where eating a clown and one says to the other. Hey does this taste funny to you?
    +2
  • K3Nv2 @ K3Nv2:
    What do you call a slow car? Retired
    +1
  • Psionic Roshambo @ Psionic Roshambo:
    Did you hear about the police car that someone stole the wheels off of? The police are working tirelessly to find the thieves.
    +2
  • K3Nv2 @ K3Nv2:
    A firefighter got arrested for assault his main claim was what I was told he was on fire
    +2
  • BigOnYa @ BigOnYa:
    What do you call a hooker with a runny nose? Full
    +2
  • Psionic Roshambo @ Psionic Roshambo:
    What do you tell a woman with two black eyes? Nothing you already told her twice!
  • K3Nv2 @ K3Nv2:
    Diddy also works
  • K3Nv2 @ K3Nv2:
    A scientist heard the word batman so he put a naked lady in a cage with a bat
  • Psionic Roshambo @ Psionic Roshambo:
    Chuck Norris won a staring contest, with the sun.
  • K3Nv2 @ K3Nv2:
    A vampires favorite thing to do is moon you
  • BigOnYa @ BigOnYa:
    What's the difference between an airplane, and Ken's mom? Not everyone has been in an airplane.
  • K3Nv2 @ K3Nv2:
    What's the difference between @BigOnYa and his wife? Nothing both want to bone me
    +3
  • RedColoredStars @ RedColoredStars:
    How much wood could a wood chuck chuck if a wood chuck could chuck norris
    +1
  • BakerMan @ BakerMan:
    how do i know? you're a guy, and he wants to bone every guy on this site (maybe, idk)
    +1
  • K3Nv2 @ K3Nv2:
    He wants to bone anything with a dick
    +1
  • Xdqwerty @ Xdqwerty:
    Good night
    +1
  • BigOnYa @ BigOnYa:
    Nighty night, big day tomorrow. Congrats.
    K3Nv2 @ K3Nv2: https://www.instagram.com/reel/C7iLZ35NrQt/?igsh=MWd2Z3U0dmNlMmNxcw==