Recent content by rip-it-up

  1. R

    Hardware Can Anyone help identify these Lite components?

    i'm not very technical at reading datasheets, but it does say connect lx1 and 2 under the chip on that pdf, thou this could just be a option for certain applications. easier just to buy a donor pcb, and transfer the componenets
  2. R

    Hardware Can Anyone help identify these Lite components?

    +AJZ 917 is the ic the bottom thing is a coil the brown things are caps nothing apart from the ic needs to go a certain way
  3. R

    Bluetooth and WiFI are not working..

    all i can tell you its for me its always the wifi chip or those 2 caps. sometimes reflowing the wifi ic, gets it working again for a day yeah guess you could check if the voltages are correct i suppose
  4. R

    Bluetooth and WiFI are not working..

    always the wifi chip in my experince yes generally the wifi chip if you haven't messed with the switch, ive had switch where those two 10nf caps have been misplaced so worth checking those, does the switch take a long time to boot on a switch logo.
  5. R

    Switch OLED. The fan is not working and joycons are not charging

    remove the diode. if its the same as first gen switches. (i have no idea) it was located near the power button fpc/fan fpc on older switches
  6. R

    Hardware Debugging faulty BCM4356 / orange screen / boot loop

    Here's my 2 cents. A switch will hang on the switch logo when there's something wrong with the Wi-Fi chip (i wish m92 did this too but I've never had that) on this note it can be very slow on this splash screen but boot but you'll notice you don't have Bluetooth or Wi-Fi. a short or something...
  7. R

    Is Switch Lite OK for BothW?

    motion control bow as well in zelda
  8. R

    I have a Nintendo Switch. Is it worth getting also a lite one?

    i actually prefer the lite over the main switch, but i think nintendo should make a companion base unit for tv, no lcd etc,
  9. R

    Switch Lite ZL always "pressed" (high resistance against GND)

    i dont think ill be able to help, you seem to know what your doing more than me. if you connect a separate joycon via bluetooth does it let you press the trigger? ( not sure why im asking that im just curios
  10. R

    Switch Lite ZL always "pressed" (high resistance against GND)

    i dont really know. the closest thing ive had is, when i pressed a certain button (think it was one of the triggers) the console would enter sleep mine was corrosion. and it fixed it. id personally test with a different daughter board, and inspect the zifs on the main board/ make sure those...
  11. R

    Did i broke this nintendo 3ds pcb?

    i dont understand why you cant just clean up the pads and install a new port.
  12. R

    Hardware Identifying the component on the Nintendo motherboard

    what voltage do you get at both sides off the resistor circled. and at pin 6 of m92. ngl, I'd probably use the tronicsfix forum for help. you seem to have changed the MOSFETs but did you test m92t36 to make sure that was working?
  13. R

    Hardware Help Switch lite. L trigger puts console into sleep mode.

    apologies for the late reply. yeah i fixed this issue, it was corrosion, so the daughter board needed a good clean
  14. R

    Hardware Identifying the component on the Nintendo motherboard

    thats not a diode its the current sense resistor ( fuse) that hardly ever blows its like my mrs. inspect bridge pins inside usb c port, and comfirm the work you have done is correct
  15. R

    old 3ds dim screen

    ive only seen this when the blacklight is broken in the top screen, i normal use a smashed screen and pinch the blacklight from it. i cant remember the 3ds mobo, but possiblily a buck regulator not boosting the voltage for backlight i would also swap out the flex cable for a speakers, if you...
See more
General chit-chat
Help Users
  • No one is chatting at the moment.
    ZeroT21 @ ZeroT21: it's a frappy moment