superfiege's latest activity
-
superfiege replied to the thread OLED boots straight to OFW 1/20 times.Did anyone solve the problem? -
superfiege replied to the thread Have problem with mod. Using 0.02 wire for all point.Hi there. Sorry for the question, but did you connect the mosfets to the chip? I dont see a wire leaving the mosfets... 1714339518 I recommend this mosfet-installation...
-
superfiege replied to the thread Hacking Hardware Picofly on "old" Samsung EMMC glitching fails sometimes.hey thank you for your support. same as before but its not a big problem for me, but i was wondering, because its the second switch where its happening. and both are ones with an old samsung-emmc. so i thought it could have a correlation.
-
superfiege reacted to rehius's post in the thread Hacking Hardware Picofly on "old" Samsung EMMC glitching fails sometimes with
Like.
slight adjustments to the boot waiting code -
superfiege replied to the thread Hacking Hardware Picofly on "old" Samsung EMMC glitching fails sometimes.I dont know why you think its because of soldering...all other switch-models work like a charm. I suspect the specific switch-model. 1712776644 hey thank you. I will desolder the instinct-chip and resolder the picofly and give feedback...
-
superfiege replied to the thread Oled mod gone wrong (cpu cap and pad missing).Backside install is very easy.
-
-
superfiege replied to the thread Hacking Hardware Picofly on "old" Samsung EMMC glitching fails sometimes.I dont think so, because when i swap the picofly with an instinct-nx it works fine :( But I dont like instinct-chips so I would prefer to stay with the picofly....
-
superfiege replied to the thread Hacking Hardware Picofly on "old" Samsung EMMC glitching fails sometimes.Am I the only one with this problem? I was wondering because it happened on two similar devices…
-
superfiege replied to the thread Oled mod gone wrong (cpu cap and pad missing).I dont know if there are any problems with the missing cap but you could try to install a single-mosfet intallation on sp1 or try a alternate backside mosfet isntallation (see picofly guide).
-
superfiege reacted to Qwasi's post in the thread Picofly install gone really bad: 3.3V trace capacitors desoldered accidentally with Like.
Drunk on confidence after successfully doing this twice in the past I ended up not treating this board with the care I should have. One bridged capacitor after using too much solder led to another and soon the whole thing came off... Trying to...
-
superfiege replied to the thread Picofly install gone really bad: 3.3V trace capacitors desoldered accidentally.Im very intersted in how this can happen! Can you tell?
-
superfiege posted the thread Hacking Hardware Picofly on "old" Samsung EMMC glitching fails sometimes in Nintendo Switch.Hey together. I modded an old Switch OLED with Samsung EMMC. Glitching works well and fast, but sometimes (about 1 out of 15) glitching fails and gives **= (No eMMC block 1 read (should not happen)) Has anyone of you had a similar or samne...
-
-
superfiege replied to the thread Hacking Hardware Switch OLED Glitching Indicator LED.Ah, I did not have time to test it right now :(
-
There are, but it means you'll have to remove the motherboard. on v1/v2/lite you can normally leave the motherboard attached while installing the modchip. Also, soldering on the cpu isn't that bad. If you have years of experience microsoldering...
-
superfiege replied to the thread Homebrew Can Switch Lite on Picofly chip run Android or Linux?.I installed both of them on many picofly chiped switch lites without any problems. Did you follow the guide on switchroot correctly?
-
-
-
-
-
-
-
-
A @ Alllrounder:Hello everyone can someone show me a tutorial on how to do the Cyclop DS evolution on the 3DS?
-
-
-
T @ Tom409179:stargate 3ds white screen in 3ds mode what do i do do i need to install firmware on flash card or what works on nds thx
-
-
-
-
-
-
-
-
-
-
-
-
-
-
